13 of 13 EMC Jobs in the Thames Valley

following would be advantageous: STM32-based platforms PCB design for highly stressed or harsh environments Electric motor controller design CAN bus implementations EMI/EMC-conscious design techniques C or C++ programming Basic understanding of turbomachinery and engine control systems Experience working within fast-paced, outcome-focused engineering teams ...

signal linear analogue circuit design. Electronics operating in challenging noise environments. Sensors incorporating high-speed ADCs (MS/s). Temperature control using TECs. EMC-conscious PCB layout and design. Phase Locked Loop (PLL) design. Frequency conversion and RF amplifiers. Photon-counting detectors. FPGA experience, particularly Intel/Altera. ...

activities for on-board processor hardware Integrate digital payload equipment and supporting EGSE Perform functional, performance and interface verification Support thermal vacuum, vibration, EMC/EMI and environmental testing Develop and maintain integration procedures and test documentation Commission and validate electrical ground support equipment Investigate non-conformances and support ...

terminate wiring harnesses and cable assemblies to IPC/WHMA-A-620 standards. Crimp, solder and lace harnesses; install backshells, connector savers and EMC/HV protective measures. Build up mechanical and electrical test setups, including fixtures, jigs and bench instrumentation. Support AIT activities on the thruster ...

electronic circuits. Work with ADC and DAC interfaces. Support power electronics design, including DC-DC converters and constant-current circuits up to 60V. Consider EMC, reliability, manufacturability and production requirements throughout the design process. Maintain PCB BOMs, design revisions and technical documentation. Product Development, Prototyping and Testing Support … based design. Experience debugging electronic hardware and embedded software. Knowledge of serial communications such as RS232, RS485, SPI, I²C or Ethernet. Understanding of EMC design principles and compliance considerations. Ability to produce clear technical documentation and engineering reports. Practical soldering experience with both through-hole (PTH) and surface ...

RS232, RS485 and Ethernet • Hardware and firmware debugging, testing and validation • Supporting power electronic designs including DC-DC converters and constant current circuits • EMC-conscious product design and compliance activities • Rapid prototyping, testing and product development • Supporting products throughout their lifecycle from concept to production What We're Looking … embedded systems • Hardware and firmware debugging experience • Ability to work across multidisciplinary engineering projects Desirable Skills: • ARM Cortex platforms • PIC microcontrollers • Power electronics design • EMC design and compliance • Ethernet communications • 3D CAD experience • Rapid prototyping and 3D printing • Product development within a manufacturing environment Why Join? • Work on innovative ...

electronic circuits. Work with ADC and DAC interfaces. Support power electronics design, including DC-DC converters and constant-current circuits up to 60V. Consider EMC, reliability, manufacturability and production requirements throughout the design process. Maintain PCB BOMs, design revisions and technical documentation. Product Development, Prototyping and Testing Support … microcontroller-based design. Experience debugging electronic hardware and embedded software. Knowledge of serial communications such as RS232, RS485, SPI, I2C or Ethernet. Understanding of EMC design principles and compliance considerations. Ability to produce clear technical documentation and engineering reports. Practical soldering experience with both through-hole (PTH) and surface ...

based products. Manage products through the full lifecycle from concept to production. Apply Design for Manufacture (DFM) and Design for Assembly (DFA) principles. Support EMC testing, product approvals and compliance activities. Design mechanical components, housings and test fixtures where required. Skills & Experience Required Degree qualified in Electronics Engineering … digital electronics design. Embedded firmware development experience. Knowledge of PCB design tools and development environments. Experience delivering products into full production. Understanding of EMC compliance and certification processes. What's on Offer Hybrid working arrangement. Bicester-based job with flexible working options. Opportunity to work on innovative technology ...

control systems Support communication via protocols such as PMBus, CANopen, Modbus, and SCPI Perform system-level analysis (efficiency, stability, thermal, fault conditions) and support EMC pre-compliance testing Conduct prototype bring-up, debugging, and fault-finding to component level Produce technical documentation and support manufacturing introduction (DFM) and field … system level Full product lifecycle experience, concept through manufacturing Working knowledge of protocols such as PMBus, CANopen, Modbus, SCPI Understanding of power conversion topologies, EMC, and thermal management Strong fault-finding skills and lab equipment proficiency (oscilloscopes, power analysers, electronic loads) 37 years' relevant industrial electronics experience Desirable Closed ...

conversion* Develop standard work and design guidelines for the power electronics domain including power component derating, creepage and clearance, circuit simulation, EMC/EMI design and PCB layout* Design and validate high-power inverters for aerospace environments, ensuring compliance with performance and safety requirements* Support development and formal qualification … devices for power electronic systems (MATLAB, Simulink etc)* Proficiency in power electronics design, including power circuit simulation, converter control, component selection and design for EMC/EMI* Ability to perform design analysis, including worst-case, tolerance, thermal, and stress* Understanding of Design for Test (DFT) and Design for Manufacture ...

technically engaging role, responsible for shaping the digital toolchains, architectures, and environments that underpin Radar Cross Section (RCS), Low Observability (LO), infrared signature, EMC/HIRF, lightning effects, antenna and RF aperture integration, radome performance, RF propagation, and electromagnetic materials . Key Responsibilities Own the delivery and continuous improvement … Develop and maintain product roadmaps, delivery plans, and prioritised backlogs. Support deployment and optimisation of EM digital solutions, including RCS/LO, IR signature, EMC/HIRF, lightning, antenna, radome, and materials modelling. Establish technical baselines, reference architectures, methodologies, and work instructions. Enable digital-thread connectivity across requirements ...

roadmap, delivery, governance, and ongoing enhancement of digital toolchains supporting: Radar Cross Section (RCS) and Low Observability (LO) Infrared (IR) Signature Modelling EMC, HIRF and Lightning Effects Analysis Antenna Design and Integration Radome Performance Modelling RF Propagation and Electromagnetic Materials Characterisation Configuration Management, Test Data Management, and Digital Thread … capabilities within aerospace and/or defence environments. Strong experience supporting one or more of the following: RCS/LO Modelling IR Signature Analysis EMC/HIRF Assessment Lightning Effects Analysis Antenna Integration Radome Performance Modelling EM Materials Characterisation Knowledge of Model Based Engineering (MBE) and Digital Thread principles. ...

roadmap, delivery, governance, and ongoing enhancement of digital toolchains supporting: Radar Cross Section (RCS) and Low Observability (LO) Infrared (IR) Signature Modelling EMC, HIRF and Lightning Effects Analysis Antenna Design and Integration Radome Performance Modelling RF Propagation and Electromagnetic Materials Characterisation Configuration Management, Test Data Management, and Digital Thread … capabilities within aerospace and/or defence environments. Strong experience supporting one or more of the following: RCS/LO Modelling IR Signature Analysis EMC/HIRF Assessment Lightning Effects Analysis Antenna Integration Radome Performance Modelling EM Materials Characterisation Knowledge of Model Based Engineering (MBE) and Digital Thread principles. ...